Contact Us

Use the form on the right to contact us.

You can edit the text in this area, and change where the contact form on the right submits to, by entering edit mode using the modes on the bottom right. 

4822 Sterling Court
Boulder, CO, 80301

+1-720-564-0373

All Products

Robotic and automation sensors for 1D laser rangefinders (LIDAR), 2D scanning lasers or LIDARs, 3D time-of-flight cameras, digital compasses, programmable USB hub, programmable ethernet controlled relays, programmable USB controlled relays.

Devantech USB to I2C, SPI, Serial Adapter

Devantech USB to I2C, SPI, Serial Adapter R348.jpg
Devantech USB to I2C, SPI, Serial Adapter R348.jpg

Devantech USB to I2C, SPI, Serial Adapter

26.00

by Devantech Ltd (Robot Electronics)

Adapter for communicating to I2C, SPI and serial buses from a USB port. Output pins may alternatively be configured as general purpose digital input/output and analog inputs.

SKU# R348-USB-ISS

Quantity:
Add To Cart

OVERVIEW

The USB-ISS module is powered from a USB type-B connector. Alternatively, it can be powered from 3.3V source by removing the "power link" jumper. The module can supply up to 80mA at 5.0V for external circuitry from a standard 100mA USB port. Drivers are required for operation under Windows. When used on a Mac OS X or Linux based operating system, the USB-ISS will manifest as a virtual serial port (CDC device) in the system device tree. This means it will show up as COMX in Windows and in the device tree (/dev/tty....) in Mac OS X and Linux platforms.

FEATURES

  • USB Powered
  • USB to I2C
  • I2C at 20kHz to 1MHz
  • USB to SPI
  • SPI at 24kHz to 3MHz
  • USB to Serial UART
  • Serial UART at 300bps to 3Mbps
  • Mounting holes
  • Horizont or vertical pin options

SPECIFICATIONS

Bootloader Link - Fit link for Bootloader mode

Bootloader Link - Fit link for Bootloader mode

I/OSPISerialI2CI2C+Serial

3.3v / 5v3.3v / 5v3.3v / 5v3.3v / 5v3.3v / 5v

I/O4SDII/O4SDASDA

I/O3SCKI/O3SCLSCL

I/O2SDOTxI/O2Tx

I/O1/CERxI/O1Rx

0v Ground0v Ground0v Ground0v Ground0v Ground

VOLTAGE SUPPLY

Use the "power link" jumper to operate from 5V, or remove it for 3.3V
The USB-ISS can operate from 3.3V or 5V. With the LEDs on, it takes approximately 20mA. From a standard 100mA USB port,  when operating at 5V, the USB-ISS module can supply up to 80mA to external devices. When the jumper is removed, a 3.3V regulator supplies the power. This regulator is capable of 50mA, so when running at 3.3V approximately 30mA is available to external devices. Do not apply your own voltage to this pin.

LEDS

The Green LED is a power indicator and is on when the module is connected to a powered USB port. The Red LED will flash whenever there is a valid I2C or SPI command received.

I/O PINS

Each I/O pin, 1 to 4, may be individually selected to be analog input or digital Input or digital output. Inputs will not accept voltage higher than the selected supply voltage, so when operating at 3.3V the inputs are not 5V tolerant. Analog inputs span from 0v to the supply votlage, and are connectedt to a 10-bit ADC.

SCL and SDA 

These pins are the I2C bus connections. They should be connected directly to the SCL and SDA pins on your I2C device. The USB-ISS module is always a bus master, and is fitted with 4.7kΩ pull-up resistors. These resistors are automatically disconnected in other modes.

SDI, SCK, SDO and CE

SDI is the SPI input to the USB-ISS, connect it to SDO on your device.
SDO is the SPI output from the USB-ISS, connect it to SDI on your device.
SCK is the SPI clock output from the USB-ISS, connect it to SCK on your device.
CE is the active low chip enable signal, connect it to CE on your device.

TX AND RX

These are logic level signals, not RS232. Do not connect this to an RS232 port without using a suitable RS232 logic level adapter.

0V GROUND

The 0v Ground pin must be connected to the 0v (Ground) on your device.

COMMAND INTERFACE

See the technical documentation for the command interface.

DOWNLOADS

Technical Documentation

3D IGES CAD Model

Windows Driver (v3)